Convection for Straight Fin Formulae and Calculator

For a straight fin with uniform cross section (assuming negligible heat transfer from tip)

Thermoplastics Applications and Molding

Thermoplastics may be softened by heat and can be dissolved in various organic solvents. Two kinds of transparent thermoplastic materials are commonly employed in windows, canopies, etc.

Boiling Point of Solvents

Boiling Point Temperature at Standard Pressure Given in deg. C Calculator

Antoine Equation Coefficient and Calculator

The Antoine equation is a class of semi-empirical correlations describing the relation between vapor pressure and temperature for pure substances.

Quadratic Formula Solver Calculator

Quadratic formula calculator solves quadratic equations using the quadratic formula. Quadratic equations are solved for real roots and complex roots.

Van Keuren Wire Diameters for Gears

Van Keuren Thread Measuring Wires used in industry should meet or exceed Federal Specification GGG-W-366B for Grade A

Power Transmission Shaft under Fatigue Loading Using ASME Code

Based on American Society of Mechanical Engineers (ASME) Standard B106.1M:1985

Automation Simulator Application CAD Computer Aided Design

This internet based application simulates various finite state machines: Deterministic Finite Automata (DFA), Nondeterministic Finite Automata (NFA), Pushdown Automata (PDA).

GMS GPS Coordinates to Decimal Degrees Calculator

Each of the 60 zones uses a transverse Mercator projection that can map a region of large north-south extent with low distortion.

Slot Gages per ASME B18.2.2

Slot Gages and Gaging for Slotted Nuts. The gages specified in Table calculator are used to determine the acceptability of the alignment and bottom contours of the slots in slotted nuts.

GPS Coordinate Conversion Calculator

The UTM system divides the Earth into 60 zones, each 6deg of longitude in width. Zone 1 covers longitude 180deg to 174deg W

Mechanism Creator and Editor Online Application

his online application can be used to explore and develop mechanisms. It is recommended that you thoroughly read the instruction on use given below

Metric Helical Coil Threaded Insert Hole Data

Metric Helical Coil Threaded Insert Hole Data per. ASME B18.29.8M - 2005. Each nominal threaded insert size is standardized in five lengths, which are multiples of the insert's nominal diameter.

Metric Clearance Holes and Tolerances per. ASME B18.2.8-1999, R2010

The recommended drill and hole sizes for metric fasteners are tabulated in this table calculator. The minimum recommended hole is the drill size and the maximum recommended hole size is based on standard tolerances.

Clearance Holes and Tolerances for Inch Size Fasteners

Clearance Holes and Tolerances for Inch Size Fasteners per. ASME B18.2.8-1999, R2010. The hole sizes for inch fasteners are patterned after USA common usage and the general clearances translated from the metric standard. The hole tolerances are based on the ISO System of Limits and Fits, as required by ISO 273.

Adaptive Control for Quadrotor UAVs Drones

Design of effective control for unmanned aerial vehicles (UAVs) requires consideration of several sources of uncertainty. These undesired uncertainties affect the flight stability and performance in an unpredictable manner.

Brittle Fracture Analysis Calculator and Equation

For materials that have little capacity for plastic flow, or for flaw and structural configurations, which induce triaxial tension stress states adjacent to the flaw, component behavior is essentially elastic until the fracture stress is reached.

Forging Wall Thickness Tolerance Calculator Grade E per. EN-10243-1

Forging grade E providing closer tolerances to assist in accommodating those instances in which the normal manufacturing standards are not adequate for function.

Tolerance Calculator Grade E Wall Thickness and Ejector Marks

Grade E per. EN-10243-1 is for closer tolerances to assist in accommodating those instances in which the normal manufacturing standards are inadequate.

Forging Wall Thickness Tolerance Calculator per. EN-10243-1

Thickness and Ejector Marks Tolerance Calculator Grade F per. EN-10243-1 for Circular Forgings