Page 15 of 87 FirstFirst ... 5 13 14 15 16 17 25 65 ... LastLast
Threads 281 to 300 of 1724

Forum: Engineering and Design Main Forum

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 02:46 PM
    • Replies: 10
    • Views: 21,567
    petronextinternational
    11-15-2018, 12:07 AM Go to last post

  1. Torque requirement calculation

    Started by switzerf, 02-19-2019 03:23 PM
    • Replies: 3
    • Views: 3,877
    Hudson
    02-20-2019, 04:34 PM Go to last post

  2. Bang Head Surface Finish After Anodizing Process

    Started by tcarlson, 02-20-2019 10:51 AM
    • Replies: 2
    • Views: 3,311
    tcarlson
    02-20-2019, 11:13 AM Go to last post

  3. Help needed to design a bed on a winch/pulley system!

    Started by missyvoid, 02-09-2019 09:45 AM
    • Replies: 5
    • Views: 7,270
    missyvoid
    02-20-2019, 04:09 AM Go to last post

  4. Real world rigging problem

    Started by dalecyr, 02-12-2019 12:39 AM
    1 Attachment(s)
    • Replies: 8
    • Views: 4,605
    Kelly_Bramble
    02-13-2019, 12:26 PM Go to last post

  5. Cutting 1060 plate

    Started by rmeyer, 01-04-2019 08:42 AM
    1060, plasma cutting
    • Replies: 6
    • Views: 5,688
    petronextinternational
    02-09-2019, 02:58 AM Go to last post

  6. Help with Proper Torque Spec

    Started by joseph_matchett, 01-15-2019 09:24 AM
    • Replies: 6
    • Views: 5,607
    petronextinternational
    02-09-2019, 02:52 AM Go to last post

  7. Calculating PSI at base of pool

    Started by Marianjela, 05-17-2012 02:27 AM
    force, l water, poo, pressure, psi 3 Attachment(s)
    • Replies: 8
    • Views: 22,336
    akash_asas
    02-08-2019, 08:30 PM Go to last post

  8. Tubing size for cantilevered aluminum beam

    Started by jdplus33, 01-30-2019 10:41 AM
    • Replies: 5
    • Views: 5,609
    Hudson
    02-07-2019, 12:22 PM Go to last post

  9. What are the best practices for machining Aluminum?

    Started by brillixa_h06, 02-07-2019 07:47 AM
    • Replies: 1
    • Views: 2,822
    brillixa_h06
    02-07-2019, 07:55 AM Go to last post

  10. Pressure Vessel Design

    Started by bryan_knapick, 02-05-2019 03:00 PM
    • Replies: 1
    • Views: 3,531
    JAlberts
    02-06-2019, 04:12 PM Go to last post

  11. perforated beam

    Started by dxt_lej, 01-28-2019 08:03 AM
    • Replies: 1
    • Views: 3,937
    Cake of Doom
    02-05-2019, 06:40 AM Go to last post

  12. Tolerances

    Started by mayank_bhanu, 02-02-2019 02:59 AM
    • Replies: 1
    • Views: 3,179
    Kelly_Bramble
    02-02-2019, 08:16 AM Go to last post

  13. Lubrication question

    Started by marklackley, 01-09-2019 11:12 AM
    brass, lube, lubricant, lubrication, mechanism
    • Replies: 0
    • Views: 3,820
    marklackley
    01-09-2019, 11:12 AM Go to last post

  14. How to get the best pressure control for branches

    Started by oldyoungguy88, 01-06-2019 09:17 PM
    • Replies: 1
    • Views: 3,529
    Kelly_Bramble
    01-07-2019, 07:53 AM Go to last post

  15. simple mechanism to open and close dual sliding Barn Doors

    Started by allwetsports, 12-24-2018 01:42 PM
    • Replies: 1
    • Views: 4,636
    jboggs
    12-27-2018, 04:05 PM Go to last post

  16. Reinforcing Steel Concrete Cover - Equipment Bases

    Started by supplm, 10-25-2014 11:26 AM
    • Replies: 2
    • Views: 4,811
    Cake of Doom
    12-18-2018, 03:32 AM Go to last post

  17. Old Cleco crane alignment

    Started by did, 12-28-2015 03:47 PM
    • Replies: 1
    • Views: 4,493
    pioneercranes21
    12-17-2018, 12:20 AM Go to last post

  18. Identifying a piece of hardware holding a radio telescope dish

    Started by ljr8675309, 12-14-2018 07:01 PM
    1 Attachment(s)
    • Replies: 1
    • Views: 2,784
    Kelly_Bramble
    12-14-2018, 07:32 PM Go to last post

  19. i need a help in project related to mechanics and design

    Started by mahmoud_qadi, 12-13-2018 03:00 AM
    • Replies: 0
    • Views: 2,884
    mahmoud_qadi
    12-13-2018, 03:00 AM Go to last post

  20. Surface Finishes by Tolerance

    Started by shawn_murphy, 12-07-2018 06:57 AM
    • Replies: 1
    • Views: 3,346
    Kelly_Bramble
    12-07-2018, 01:33 PM Go to last post
Page 15 of 87 FirstFirst ... 5 13 14 15 16 17 25 65 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules