- Caltex Capella 68 or Shell Calvus 68
- Need some advice on getting started
- Help with Compression Shocks
- Transitioning to mechanical engineering, where to start?
- Cantilever beam sizing
- Fatigue Reliability on Endurance Limit
- Trouble with torsion spring calculations
- Becoming a Mechanical Engineer
- Thinking about going contract to full time, not sure how much to ask
- Need some help with lever design
- Need Modulus of Elasticity of Flexible PVC
- manufacturing methods for precision small hole making
- Wind Turbine Drag
- Turbines to recharge an electric vehicle
- Help with complete novice
- Advantages and disadvantages of bevel gears
- plz help with his problem. how to approach it.
- How to fix leakage in hydraulic cylinder?
- Pneumatic System
- How to calculate distributed point load for a cantilever?
- Age Hardening 17-4 PH
- Rigid frame analysis
- heat transfer- conduction problem
- Need Very Simple Help on a School Project
- E value for Phenolic LE
- Troubleshooting Shaft Wear
- Mechanical products
- Mini Project on Engineering Material (Polymer)
- Force required for tipping of structure
- Reducing/Dampening Noise and Vibrations in a High impact system
- Parallel Pump Operation for BFP
- (NEW) Help with Electromagnetic Braking Principles
- Engineering Thermofluids - Convective heat transfer and steady state conduction probl
- air /water
- extraction of water from air
- Point load
- Gear torque --- help me please
- Understanding the actual mechanics of what goes on in flow in pipes
- Trying to get reaction force on bolt.
- Strain Gauge Data
- Does total reaction force exerted on bolt need to take account clamp force ?
- type of support for this beam?
- Riveting Stuff
- How do I represent load distribution on beam for equipment that is half out?
- why type of support for diving board is assume as pin/roll, why not fix support?
- How do I calculate tension force for scattered bolt on plane
- Polyrow Pumps
- Pressure in heating system
- Calculating the rise of a beam beyond it's support
- Need an answer (Power trasmission belts )
- Non-contact High Speed Braking System
- Coal fired boiler
- How to calculate the torque that a flywheel will deliver.
- Strain Gauges. How do I pick the right one?
- solar water pump
- One way valve is there a kind like this ?
- Cable Winch with programmable attraction
- Pull out force for aluminium base with self tapping screw
- Calculating Tolerances on a Part
- Measure of Basic Dimension
- Self Activating Trigger/Timer
- why plastic for this piece?
- Vapor/bubbles after pump
- Help with making a custom office chair for Music listening
- Help with Aquarium stand made of Aluminium
- Torque required to move load
- Heat transfer through convection & radiation
- Low friction ratchet mechanism
- Join two links by pushing and creating revolute joint
- Chain snaps
- Internal spur Gear Design
- Engine in-cylinder pressure validation
- How engineering forums help engineering students ?
- Changing from cam followers
- How do i calculate the strength of a friction hinge?
- How to apply a constant, gradually increasing load to a machine.
- Rack & Pinion versus Lead/ball Screw
- Overhead magnetic conveyor design considerations
- Crown and spur gears
- A2-70 Material for Washers
- Importance of Machining Tantalum
- Slider crank torque
- Contact pressure - screw pretension
- The Journal Bearing Temperaure Raising During Rainy
- Does this mechanism have a name?
- Stress acting on Rack?
- I need help to findout the mechanism
- Compression Force on square tube
- Horizontal Rod Size Required
- Plastic Part Carrying Torque and Radial Load
- Siemens plc- lost back-up and unable to access the programs.
- How do I determine a desired Charpy/Izod result?
- Urethane, 90 Duro strain energy
- AISI 304 L Tube to tube-sheet weld failure
- Repair options for leakage in a regenerator (Heat exchanger)
- gear design software
- Belt and Pulley
- I need to lift a roof
- Metric gears
- calculation of water flow rate in heat exchanger (water-air type)