- Carbon fibre strength
- Aspen one help
- Unable to figure out the flatness tolerance specified for an equipment mounting
- Heat Treat Call Out
- Help on making ramps: aluminium tube deflection and welding
- Finding appropriate bolt torque when bolt bolt is used on PVC surface
- rack & pinion tangential force calculation
- Bean Deflection Macaulay’s Method
- Design Calculations of Bolted tubesheet on a annular ring welded to the shell
- Automated door two actions...
- Mechanical Engineer looking for some career advice
- Hi Gang,
- Drop shock calculation
- Compressibility of copper gaskets/sheets
- Engineering and Manufacturing Economic Data
- traffic signal pole design
- Limit Gauge Question
- Bad Connector Design / Choice
- Hinge design
- shear pin diameter
- Requirement Analysis
- Assist with Miniature Bearings Selection for WINDSWIMMER Prototype.
- Conductive Gels of shore OO or softer
- Hollow cone beam loading question
- Rotation using two (four) hydraulic cylinders HELP!
- How To Calculate Forces In A Sheet Metal Bender?
- Cyclic Loading of Fastener and Fatigue
- Functional and autonomous smartphone
- Question about True Position (Cartesian Tolerance)
- Restoration of Connection in Precast Concrete Structure
- How to determine the force on the linkage
- Allowable bearing capacity
- Difference between 2 waterwheels
- New here. Bolt question
- Resolution of Forces and Moments on a machine structure
- UHMWPE question... two tubes of same material in exact same use/wash conditions etc
- Can anyone help me identify which material is better?
- Find force of bolt
- hydraulic pump/ motor question
- Surface Finishes by Tolerance
- i need a help in project related to mechanics and design
- Identifying a piece of hardware holding a radio telescope dish
- simple mechanism to open and close dual sliding Barn Doors
- Cutting 1060 plate
- How to get the best pressure control for branches
- Lubrication question
- Help with Proper Torque Spec
- perforated beam
- Tubing size for cantilevered aluminum beam
- Tolerances
- Pressure Vessel Design
- What are the best practices for machining Aluminum?
- Help needed to design a bed on a winch/pulley system!
- Real world rigging problem
- Torque requirement calculation
- Surface Finish After Anodizing Process
- Shear stress on spline teeth
- Missing eddy currents in copper?
- Engineering ********** that combine mechanical, electrical and programming
- Gas fired boiler efficiency calculations/ through losses
- How to manufacture this spiral part?
- Industrial Vacuum Chamber Design - Need Help for Design Calculations
- Four Bar Linkage Angles
- Remagnatizing
- Low Friction Fabrics
- Ab Toning Systems
- help to estimate the pulling force in this pulley-cable arrangement
- Rivet related question, how many and what size?
- How to reduce deflection on this DIY table.
- Who Is The Manufactuerer of this Heavy Hex Nut
- Motorized Stages for smallest incremental movement possible?
- Help needed in determing the tip load capacity of a particular pole type
- Help Needed figuring out weight load of angle iron please
- Help Plz!!! Scissor Lift, need help.
- Ways to lessen wear caused by a steel fixture
- Plastics Shredder Design
- Reference for Table
- Air tanks in parallel and series
- Need for advice
- Material "Slash sheet description"
- SolidWorks Stress Analysis question
- Uni project Help
- Heat Exchanger Question
- Lever arm design
- Pre-load on needle roller clutch
- Pneumatic hammer prototype
- Stainless steel floor drain
- Back yard jet engine?
- Physical height calculation of RA surface finishes.
- Motor and Gearbox Pairing
- Structural safe loading calculation
- Tempered glass "burst" calculation
- Deflection and Stress of arm with an angle
- what kind of electric motor with reducer is needed?
- Motor with brake and gearbox for high torque application
- Machinery's, Roark's Stress and Strain, etc.
- Rule of thumb for drilling holes in I beam flange
- Rule of thumb strength question. Brass vs stainless steel
- Best spline type - rotational force into plastic
- Learning about turbines and thinking about the output.