- Help me choose a plastic.
- Needing help with a Allowable force a Beam w/ moment. Bolt Design
- New kind of leaf blower - Comments?
- How to create a vertical movement
- Clip that will release under load?
- Tool to Apply a Radial Force on Tubes
- Square tubing load limit
- Education Questions
- A Challenge - To Any Structural/Electrical/Areo Engineers, Physicists, Scientists
- Electrical Engineering or Engineering Management?
- pressure reduction through process
- NEEDED - Swivel hardware solution.
- Forging Ratio query - Reg
- Aluminum C channel specs
- 1.813" 10-Stub Acme
- Tandem Axle Trailer Loading
- Square tubing options for stilts
- Back yard jet engine?
- Newbie needing your guidance in creating a slowly rotating device...
- Swaging Wire Rope Stop Sleeve
- Material thickness before shear
- Arc tolerance
- Submarine project hull strength
- Simulation sandwich structure ANSYS Mechanical
- U-Bolts rotational capacity
- Cantilever weldment or bolted connection
- S beam secion details
- Mechanical location tolerance capabilities
- Aluminium 6060 T66/1050H14 Heat failure question
- PE Architectural
- Static Mixing Improvements for Disposables
- Checking Dimensions of a Half disk
- Heavy duty stand or shelf for 24" electric clothes dryer
- I need help with force calculation
- Difference in Wire Rope
- CCGT in jet engine
- What is a good bearing material for use with aluminum?
- lego Differentials in parallel
- RV Bed Frame Design
- Micro pneumatic powered generator
- Designing a Pipe bridge Using angle irons across a span of 6.5m. Need Help
- Aluminium Standards Calculations
- Tilting Mechanism
- Car Grille Aerodynamics
- Looking to calculate the mechanical advantage of a toggling lever (t-shirt press)
- reference electrode could be used to measure the potential of a steel structure
- Rubber Bladder Design
- Mathematical modeling of the deflection of a rod
- Compromised 10" joists with 6" plumbing holes braced instead of sistered?
- Interview Help
- Need help making something.
- Stress in fillet weld. Two conflicting sources for calculating shear stress
- Spur Gear design - how to remove interference
- how thick is my sheet?
- Hanging a motorcycle on a Fifth Wheel
- wheel power distribution by differential in a turn
- I'm stumped! Mini hydraulic jewelry press spec question, please help!
- Functional Back Brace For a Costume
- clay mixer or pug mill torque calculation
- Hydraulic Manifold Design Issues
- Design and engineering
- Calculating Total Deflection for Constant Load
- Ansys combined analysis of pressure and vibration
- Electrical signal attaches unit to free moving cable
- 6063-T5 aluminum help
- ⛔★ Help me design a simple time delay (not electrical)
- centrifugal pump operation
- Automated sample extraction from oven?
- Choosing an efficient compressor
- Newbie with alot of MFG questions for plastic light case
- Automated Tool Control
- Tightening torque for socket head countersunk screws
- An elevator/skip that is driven by the Earth's electric field.
- Material replacement
- hello everyone ,please help me out to specify a tolerance
- Ball screw rpm question
- Tracker Challenge
- Force transmitted along the helix of a thread
- Cone through an angled hole problem...statics..
- Is this 10:1 ratio correct...can you help me?
- how to calculate force required for automated retaining ring installation - HELP!!!
- Mechanical Engineering Important Question
- Calculate reaction force on bolt due to the force of object. Is this the right way?
- Clamp force/tensile force due to torque consideration.
- Bolt connection is Fix-Fix or Pin-Pin support?
- Is x=0 the same as "at the support" in the Cantilever Beam Calculator Formula?
- which bolt experience the highest tensile force. close to c.g or outermost
- How pressure regulator work ?
- Machine malfunction due to Cantilever design!
- Material Storage Rack by using Steel Angle
- design of thermic fluid pump
- Design of digital calendar, clock and 4 individual 24 hour alarms
- Attach Copper Washer to Bike Wheel to pass electrical current via Carbon Brush
- Screw Torque VS attachment material
- Ergonomic limits for thumb and 1st finger?
- How to select cable under tension....
- Spur Gear Rack
- Ring with Links as Shear Springs Tunnel Model
- How to calculate air cleaner volume for passenger cars
- Will this work? Steel beam question